Skip to content
HollandLanding Garage Door Pros
Open 24/7(289) 803-1641Open 24/7
Two coiled steel cables with loop and stop ends on a workbench. — Garage Door Cable Replacement, Newmarket
Gloved hand holding a white garage-door roller beside its track, with two loose rollers and a red tool on a tray. — Garage Door Roller Replacement, Newmarket

Springs · Newmarket

Garage Door Cable Replacement

After years of slushy winters the cables look thinner near the bottom brackets, with rust streaks running down the door where they attach.

Call (289) 803-1641

In plain words

Cables are replaced as a pair, and there is a practical reason. Both went on the door together, have made the same number of trips and have sat in the same slush, so when one fails the other is close behind. A new cable beside a stretched one also pulls the door slightly out of level. Fitting two matched cables of the same length and construction lets the technician set the door dead level, tension both sides equally and leave a counterbalance that shares the work evenly for years. It also means one visit rather than two.

Sound familiar?

The car bumper kissed the door on the way in. The bottom panel has a dent, the bracket in that corner sits crooked, and the cable on that side has jumped and gone slack, so the door reverses every time it tries to close.

How the visit goes

Garage Door Cable Replacement

How the visit goes

Technician in safety glasses holding a metal bracket against the edge of a partly raised gray rolling steel door.
Full-glass garage door with black frames, an orange stepladder, a level, a drill and a shop vacuum on the concrete floor.
  1. Making the door safe to work on

    Nothing is touched until the door cannot move. The technician pulls the opener's release cord so the motor is out of the picture, clears the opening, and clamps the track just above a roller or props the door if it is jammed partway. If one cable has let go, the door is probably tipped and binding in the track, with its weight resting unevenly on the remaining cable and spring, so the first job is to take that weight on clamps or a support. Only then does the assessment of drums, springs and brackets begin. This step is calm and deliberate, and it is what allows every later step to be done with both hands.

  2. Removing the old cables

    Each drum's set screws are backed off so the drum spins freely on the shaft, and the old cable is unwound from its groove and the stop slipped out of its slot. At the floor, the loop is lifted off the bottom bracket pin, or the clevis pin and cotter pin are withdrawn where the door uses them. The old cable is kept for a moment to measure against its replacement and to show you the wear that caused the call. On an extension door the cable comes off its pulleys and the adjusting clip at the track hanger. Both sides are stripped before anything new goes on.

  3. A door that runs level and quiet

    The first thing you notice is a door that rises squarely, with both bottom corners leaving the floor together and the top section staying flat as it turns into the horizontal track. The bottom seal meets the slab along its whole length, so the draft and the strip of daylight at one corner are gone. The opener sounds calmer, because it is moving a balanced door rather than dragging a crooked one, and it stops reversing for no apparent reason. If you lift the door by hand with the opener released, it moves with light effort and holds where you leave it. That is what a correctly cabled door feels like.

Garage Door Cable Replacement

In the van

  • Torsion springs and winding cones

  • Cable drums, matched pair

  • Winding bars

  • Clevis pins and cotter pins

  • Drum set screws

Aluminum tray holding about a dozen garage-door rollers on steel stems, some with white nylon wheels and some with worn metal wheels.

Garage Door Cable Replacement

What affects the quote

  1. One cable or the pair

    Cables are normally renewed together, and the quote reflects two cables and the work of setting both sides level. Where one side was recently replaced, that is discussed on site.

  2. Door height and lift type

    Cable length follows the door height and whether the hardware is standard lift, low headroom or high lift. Taller doors and high-lift conversions take longer cables and specific drums.

  3. Oversized, commercial or high-lift doors

    Doors taller or wider than a standard residential opening, or fitted with high-lift hardware, use heavier cables and drums and take longer to set up, which the quote reflects.

What to have ready

  • Is it a single or a double door, and roughly how tall?
  • Do you have the door's manual or a label showing the model?
  • Is the door closed, fully open, or stuck partway?
Call (289) 803-1641

Garage Door Cable Replacement: questions

Questions
What stops the door from falling if a cable lets go?

It depends, and not reliably. The other cable and its spring may hold that corner so the door tips and wedges in the track rather than falling square, and the rollers binding can add some resistance, but neither is dependable: the door can still drop unexpectedly on the failed side. Some doors also carry a broken-cable device on the bottom bracket that grips the track if a cable fails. Because the door may not be held at all, the technician clamps and supports it before doing anything else.

Should I lubricate the cables?

A light film, yes. A mist of silicone or a lubricant made for garage doors on the cables, especially the lowest stretch near the brackets, sheds moisture and slows rust. Avoid heavy grease or oil, which holds grit and salt against the strands. The springs, hinges, roller bearings and bracket pins take the same product a couple of times a year, and the tracks are simply wiped clean.

Do I need new cables when the springs are replaced?

Often it is sensible. Cables and springs are similar in age, and with the counterbalance already unloaded the extra work of fitting new cables is small. The technician inspects them and advises: cables with bright, tight strands and clean loops can stay and simply be re-tensioned, while cables with any fraying or rust at the bottom are better renewed now than in a separate visit later.

Related services

Garage Door Cable Replacement near you

Call(289) 803-1641

Request a visit

Or call (289) 803-1641 · open 24/7